← Polypropylene Insulated tanks
Insulated 2,000 Gallon HDPE Vertical Tank 1.9 102
Part # HDPE-VTB02000-102-1.9-NAT-INS
Tank Specifications
- Capacity
- 2,000 gallons
- Dimensions
- 102" Diameter × 80" Height (8 ft 6 in × 6 ft 8 in)
- Specific Gravity
- 1.9
- Color
- White
- Tank Type
- Vertical
- Wall
- Single Wall
- Installation
- Above-ground tank. Do not install below grade.
- Lid
- 16"
- Resin
- HDPE
- Manufacturer
- Bailiff
- Weight
- 450 lbs
- Meets or Exceeds ASTM D 1998-21 Wall Thickness Specifications.
- All tanks go through Hydrostatic Testing before release.
- 2" Closed-Cell Polyurethane Spray Foam Insulation on the Sides and Top
- White Elastomeric Coating over the Insulation
- Insulation Rated R-6.7 per Inch of Thickness
- FDA Approved Resin
- Infused with UV Inhibitors to Prolong the Life of This Tank
- Rated for Atmospheric Pressure Only
- Lifting/Tie-Down Lugs Molded-In
Available Fittings and Options
We outfit tanks to customer specifications.
Manufacturer Information
- Manufacturer
- Bailiff
- Part Number
- HDPE-VTB02000-102-1.9-NAT-INS
- Warranty
- Limited 3-Year Warranty
Resin Information
- Resin
- HDPE
- Color
- White
- Temperature
- HDPE has a maximum continuous use temperature of 120 F.
- Chemical Compatibility
- Chemical Compatibility Database
Shipping Information
- Ship Width
- 102"
- Ship Length
- 102"
- Ship Height
- 86"
- Ship Weight
- Ship Class
About Insulated Tanks
Insulated tanks are covered with closed-cell polyurethane spray foam, rated R-6.7 per inch, and sealed with a white elastomeric coating that protects the foam from UV. HDPE handles a wide range of acids, caustics and water-based chemicals and is the most economical resin.
- Standard insulation is 2 inches thick (R-13.4); 3 inch (R-20.1) and 4 inch (R-26.8) are available on request.
- The sides and top of the tank are insulated.
- A good fit for freeze protection and for chemicals that crystallize or gel in cold weather, such as 50% sodium hydroxide and DEF.
- Heat tracing can be added when insulation alone is not enough.
Frequently Asked Questions
How thick is the insulation?
Standard insulation is 2 inches of closed-cell polyurethane foam (R-13.4). We also offer 3 inch (R-20.1) and 4 inch (R-26.8) on request.
When do I need an insulated tank?
Use an insulated tank for freeze protection and for chemicals that crystallize or gel in cold weather, such as 50% sodium hydroxide and DEF (diesel exhaust fluid).
Can heat tracing be added?
Yes. We offer heat tracing in combination with the insulation when insulation alone is not enough.
What do the 1.5, 1.9 and 2.2 SG ratings mean?
The SG (specific gravity) rating is the heaviest liquid a tank is built to hold. Water is 1.0. Tanks rated 1.5 SG are for liquids up to 12.5 pounds per gallon, 1.9 SG up to 15.8 pounds per gallon and 2.2 SG up to 18.3 pounds per gallon. Choose a rating at or above the specific gravity of your liquid. See our specific gravity chart.
When you need to stabilize the contents of your tank to maintain a temperature or prevent freezing, our insulated tanks can be the answer.
Insulation can be combined with Heat Trace to keep tank contents at a pre-set minimum temperature. This is especially beneficial for chemicals like Sodium Hydroxide (Caustic Soda) where the liquid becomes viscous and hard to pump at temperatures below 65 F.
Outfit this tank
Fittings & Options for This Tank
We install fittings and accessories at our plant so your tank arrives ready for your piping and controls. See all fittings & options.
Welded couplings and flanges, bulkheads, bolted and PVC bulkhead flanges, sanitary tri-clamps.
View →Vents, Valves & PipingPVC U-vents, ball and check valves, top fill and top drain lines.
View →Level IndicatorsReverse float gauges and ultrasonic level sensors with display.
View →Tank Options & AccessoriesTie-downs, leak detection, insulation, heat trace, ladders and cages.
View →